Sequent Direct Injection 2.0
Sequent Direct Injection 2.0
Sequent Direct Injection 2.0 is a serial sequential multipoint gaseous injection system (or master & slave). As for the other Sequent systems, gas injection occurs into the intake manifold, whereas the petrol injection directly occurs into the combustion chamber. This approach allows having the same installation simplicity appreciated on the other systems, and can use the same mechanic components, with evident advantages in terms of components validity.
PDF İndir Karşılaştırmak 
Gaseous phase filter – LPG
• IN and OUT gas fitting ø 12,5 mm
• Cartridge material glass fiber
• Working Pressure 0 ÷ 4,5 bar
• Operating temperature: -40 °C ÷ 120 °C
• Approval: R67-01 and R110
Hp level sensor high pressure – CNG
• CNG pressure sensor
• ø outside 50 mm
• Range 0-400 Bar
• Working range 0-260 Bar
• Working voltage from 5 to 10 V
• Output Voltage Range (pressure): 0,5 to 4,5 V
• Connection 1/4 BSP
• Approval: R110
Genius Max reducer – LPG
• Diaphragm single-stage type building
• Adjusted pressure: 150 kPa relative to the intake manifold pressure
• No bleeding operation needed
• Approval: R67-01
Genius MB reducer – LPG
• Diaphragm single-stage type building
• Adjusted pressure: 800, 1.200 or 1.500 mbar relative to the intake manifold pressure
• No bleeding operation needed
• Approval: R67-01
BRC IN03 MY09 electroinjector LPG/CNG
• Floating shutter with ultra low friction
• Impedance: 1,66 / 1,7 mH a 20 °C
• Temperature: -15°C ÷ 120 °C
• Voltage: 6 V ÷ 16 V
• Seal: Rubber on metal
• Approval: R67-01 and R110
Gas ecu – LPG / CNG
• Automotive microprocessor 16 bit – 64 MHz
• Operating Temperature: -40 °C + 90 °C
• Watertight through immersion
• According to automotive norms for protections and inlet/outlet signals
• Operating voltage: 8 V ÷ 16 V
• Sensors and actuators diagnosis compatible with EOBD
• Communication and reprogramming with PC through K-line
• It supports KWP2000 communication protocol
• It supports CAN 2.0 communication
• EMC compliant
• 2 ECU Versions: up to 6 injectors and up to 8 injectors
• Integrated injectors cut and emulation
• Approval: R67-01, R110 and R10
Zenith reducer – CNG
• Double stage type with diaphragms
• Water Temperature Sensor
• Adjusted pressure: 2.000 mbar relative to the intake manifold pressure
• No bleeding operation needed
• Δp adjustable between 2.000 and 2.500 mbar
• Approval: R110
One Touch changeover switch
• SMD single-stable changeover switch
• ø outside 26 mm
• Possible installations:
– built-in with ø 23 mm hole and 2 mm dimension
• With integrated Acoustic indicator (buzzer)
• N° 4 green Leds for level indication
• N° 1 bi-colour (green/red) Led for mode working indication
PTS Sensata sensor (on rail) low pressure LPG / CNG
• Gas temperature and pressure sensor
• Mass: 22 g
• Overall dimensions: ø= 24 mm, h= 64,5 mm
• Integrated connector
• Power Supply Voltage: 5 ± 0,1 VDC
• Supply Current: 10 mA MAX
• Output Voltage Range (pressure): 0,5 to 4,5 V
• Operating temperature -30 °C ÷ 130 °C
• Approval: R67-01 – R110
Teknik özellikler
| Supply | LPG-CNG |
| Cylinders | up to 8 |
| Gas ECU | SDI 2.0 - 56 SDI 2.0 - 154 |
| Gas ECU Connector | FCI 56 Ways TYCO 154 Ways |
| Gas Ecu Body Material | Aluminium |
| Gas Shut-off Solenoid Valves | 2 |
| Reducer - Fittings inlet outlet elbows | LPG Brass and Plastic / CNG Iron |
| Internal Petrol Injectors Emulation | Inductive |
| Gas Temp. Input | ✓ |
| Gas Pressure Input | ✓ |
| Water Temperature Sensor on Reducer | ✗ (**) |
| N° Lambda Oxygen Input | 2 |
| RPM Signal | ✓ |
| MAP Sensor | ✗ (**) |
| CNG Internal Timing Advance Processor (*) | ✗ |
| Communication with OBD (K and CAN) | ✓ |
| Sequential Fuel Switch OVER | ✓ |
| Injectors Rail | Aluminium - Plastic |
| Injectors Type | IN03 MY09 |
| Gas Level Indication | Switch |
(*) For using CNG Timing Advance Processors please make reference to respective Sequent systems handbooks
(**) Required only for specific vehicles model
